Australian Truck Weight & Load Planner
Plan a heavy vehicle load before it rolls: sum axle group masses, work out payload against tare and a gross figure you enter, see how moving the load changes the reactions at each support, and size the restraint forces a load needs under stated acceleration criteria. It computes against limits you enter - it holds no legal limits of its own and makes no compliance determination.
Where the vehicle is operating. Interstate travel is a separate question; this is not taken from a registration plate.
Axle groups
Measured mass, and the limit you are working to. The limit is yours — from a permit, a plate or a rating you have in front of you.
Over a limit you entered
Gross mass: 43,350 kg
Payload: 25,350 kg — only meaningful if the tare describes this same combination.
- Steer group is within the 6500 kg limit you entered, with 500 kg to spare.
- Drive group is 350 kg over the 17000 kg limit you entered.
- Trailer group is within the 20000 kg limit you entered, with 0 kg to spare.
- Gross mass is within the 45000 kg limit you entered, with 1650 kg to spare.
- Gross mass has not been checked against Western Australia rules. That profile is not enabled here: its sources (S02, S03, S04, S06, S25) still need transcription and independent review. Enter your own limit to compare against instead.
A number inside every limit you entered is not a statement about compliance, route access, load stability or fitness to drive.
Past the rear support is allowed: it is how a trailer gets loaded.
Predicted - verify by weighing
Front support: 4,000 kg · Rear support: 6,000 kg
Restraint demand: 78.453 kN forward, 49.033 kN sideways and rearward, 19.613 kN upward.
Two supports on a rigid deck, the load treated as acting at a point, at g = 9.80665 m/s². This is a simplified statics result in mass-equivalent units, not a multi-articulation vehicle model: a dolly, a fifth wheel and a drawbar have distinct load paths and none of them is modelled here. It cannot replace a weighbridge ticket.
The demand figures are the directional requirements - 0.8 of the load's weight forward, 0.5 sideways and rearward, 0.2 upward. They are NOT a strap-count formula. How many lashings a load needs depends on the arrangement, the hardware, the angles, the pretension and the friction, and rated capacity and pretension are different properties. None of it is calculated here: the arrangement solver needs authoritative technical material this build does not have, and guessing a lashing count is the one answer this tool must never produce.
Runs entirely in your browser. Your input is not uploaded or stored.
Before you rely on this: First-pass guide only. Verify safety-critical or regulated work against the relevant standards, your project requirements and a qualified professional.
How to use this calculator
- Enter each axle group's mass to get the gross figure, or enter gross and tare to get payload.
- Enter the limit that applies to your combination in the limit field. The tool compares against that number and tells you the excess; it does not know what your limit is.
- On the loading position section, enter the load mass and where it sits between the supports to see how the reactions split, including uplift when the load sits outside the supports.
- Enter the restraint acceleration criteria you are working to and read the demand forces the load produces in each direction.
How it works
Gross mass is the sum of the axle group masses; payload is gross minus tare. Excess is the amount by which your entered figure exceeds the limit you entered - all three are plain arithmetic over your own numbers.
Load position uses the simply supported beam reaction: a point mass between two supports divides between them in inverse proportion to its distance from each. A load placed outside the supports produces uplift at the far support, which is reported as a negative reaction rather than clamped to zero.
Restraint demand is the load mass multiplied by the acceleration criteria you state, giving the force the restraint arrangement must resist in each direction. It is a demand figure, not a lashing count.
Worked example
Worked example. A 12 t load sitting 2 m from the front support on a 6 m deck between supports puts 12 x (6 - 2) / 6 = 8 t on the front support and 12 x 2 / 6 = 4 t on the rear. Slide it 1 m forward and the front takes 10 t - which is how a load that is within gross mass can still overload one group.
Common mistakes
- Expecting the tool to know your legal mass limit. It does not, by design - every limit it compares against is one you typed in.
- Mixing tonnes and kilograms between fields.
- Treating a restraint demand force as a number of lashings. It is the force to be resisted; selecting hardware to resist it is a separate job with its own rated capacities.
- Assuming a passing gross mass means the combination is legal. Mass is one requirement among many, and this tool addresses only the arithmetic.
Tips
- Work from a weighbridge figure where you have one; a calculated gross is only as good as the tare you entered.
- Check the reaction split as well as the gross. A combination can be under its gross figure and still be over on one axle group.
- A negative reaction means uplift. It is reported rather than hidden, because a load that lifts a support is a real condition and not an arithmetic error.
Frequently asked questions
Does this know Australian mass limits?
No, and that is deliberate. It holds no General, Concessional or Higher Mass Limit figures and no jurisdiction profile is enabled anywhere in it. Every limit it compares against is one you enter, and every check it returns says so.
Why not just build the limits in?
Because getting them wrong is worse than not having them. Mass limits sit in the Heavy Vehicle (Mass, Dimension and Loading) National Regulation and in jurisdiction-specific notices and exemptions, they have been under reform, and public secondary sources contradict each other on current figures. Encoding a number from a blog post and presenting it as a limit would be a safety problem, not a feature. The operative instrument and a competent reviewer are what that needs.
Is this a compliance check?
No. It is a planning and arithmetic tool. It does not determine whether a vehicle is legal to operate, and a result from it is not evidence of compliance. Use it to plan a load and to find problems early; use your operative instrument, your permits and your own assurance process to decide whether you may drive.
What does a negative reaction mean?
Uplift. The load is positioned such that it tends to lift one support rather than press on it. The tool reports the negative figure instead of clamping it to zero, because clamping would hide a condition you need to know about.
Does it account for load-sharing suspension, axle spacing or tyre type?
No. Those affect which limit applies, and since the tool holds no limits it has nothing to apply them to. It computes masses, reactions and restraint demand from the figures you give it.
Does my data leave the browser?
No. Everything runs in this page on your device and nothing is uploaded.
Related tools
- Australian Truck Fatigue Planner
- Towing Payload Calculator
- Trailer Tongue Weight Calculator
- Manual Lifting Calculator
- GVM & GCM Compliance Calculator
- Caravan Tow Safety (85% Rule) Calculator
Explore more in Automotive, 4WD, Towing & EV.
Cite this tool
Zerdly. (2026). Australian Truck Weight & Load Planner. Retrieved from https://www.zerdly.com/tools/australian-truck-weight-load-planner/
Tip: Enter any known values to calculate the remaining results.
Designed to run locally in your browser. Tool inputs are not intentionally stored by Zerdly unless stated otherwise.



