Lens Equivalence Calculator
Match focal length, field of view and approximate depth of field across camera formats — including sensor crops, focal reducers, teleconverters and anamorphic setups.
Source — the camera and lens you have
Generic assumption — a round example, not a claim about every camera in this category.
Millimetres, not megapixels or nominal sensor inches.
Target — the camera you are matching to
Generic assumption — a round example, not a claim about every camera in this category.
Millimetres, not megapixels or nominal sensor inches.
Matching
With different aspect ratios, one focal length cannot match every edge.
The lens you actually have
Optional. The exact requirement above does not change — this only says how close your kit gets to it.
Enter the focal lengths you own to see the nearest match.
Enter the widest f-number to check it can be reached.
Geometry at a glance
Result
Target needs a lens of
52.5 mm
at approximately f/3 for a matching depth of field
Horizontal match, 1.5×. Same viewpoint and final viewing assumptions.
- Source lens, as marked
- 35 mm f/2
- Target lens, to set
- 52.5 mm
- Depth-of-field equivalentNot an exposure setting
- f/3
- Actual effective apertureWhat the lens transmits
- f/2
- Exposure consequenceGeometric estimate, equal shutter and transmission
- 2.25× ISO · +1.17 stops
- Keep the same exposure insteadDepth of field will differ
- f/2
- Entrance pupil, source
- 17.5 mm
- Source retained area
- 24 × 16 mm
- Target retained area
- 36 × 24 mm
- Angles H / V / D, source
- 37.8° / 25.8° / 44.8°
- Angles H / V / D, target
- 37.8° / 25.8° / 44.8°
- Full-frame equivalent, source (horizontal)
- 52.5 mm
A sensor crop does not change the lens’s f-number, transmission or exposure per unit area. The depth-of-field equivalent above is a framing-matched comparison, not an exposure setting.
How to use this calculator
- Pick the recording mode on the camera you are shooting with, or type its active image area in millimetres.
- Enter the lens you have on it: actual focal length and marked f-number.
- Pick the camera you are matching to, or type its active area.
- Choose the axis to match on — horizontal is the usual choice for a wide shot, vertical if you are protecting headroom.
- Read the target lens figure. The depth-of-field equivalent aperture sits beneath it, labelled separately from the actual aperture.
- Open Advanced optics for focal reducers, teleconverters, anamorphic squeeze, a measured T-stop or a depth-of-field readout.
How it works
Equivalence is one ratio. For the axis you choose, the tool takes the virtual (desqueezed) size of that axis on each setup and divides target by source. Call that k. The target then needs an effective focal length of k times the source's effective focal length, and — for spherical lenses only — an aperture of k times the source's effective f-number to get a comparable depth of field.
The active recording area does the work, not the camera's name. The same body can read the whole sensor, a centre window or a resampled full-width image, and all three can be labelled 4K. Only the published active area in millimetres distinguishes them, which is why every preset here is a recording mode rather than a camera, and why custom dimensions are a first-class option rather than a fallback.
Native and effective values are kept apart. A lens's marked focal length does not change because a smaller sensor sits behind it — the sensor records less of the same projected image. An optical adapter is different: it genuinely changes the system. A 0.71x reducer makes a 50 mm f/2 behave as 35.5 mm f/1.42, and a 2x teleconverter makes the same lens 100 mm f/4. The answer you dial into a lens barrel is the native figure, so the tool shows both.
Angles of view come from the retained area and the effective focal length: the horizontal angle is twice the arctangent of half the virtual width over the focal length, and likewise for vertical and diagonal. These are rectilinear, infinity-focus approximations. Fisheye projections follow a different model and are not supported.
Worked example
A 35 mm on APS-C, matched onto full frame. Source 24 × 16 mm with a 35 mm f/2; target 36 × 24 mm, no adapters, horizontal match. The horizontal scale k is exactly 1.5, so the full-frame camera needs a 52.5 mm lens. For a comparable depth of field it needs about f/3 — and at that aperture, with the same shutter and the same transmission, it needs 2.25× the ISO, or +1.17 stops, to render at the same brightness. Shoot it at f/2 instead and your exposure settings are unchanged; the depth of field is simply shallower than the source's.
Common mistakes
- Applying a camera-family crop factor on top of a mode that already has the crop baked into its dimensions — that double-counts. The additional crop field is for a window on top of the selected mode.
- Entering a bare-lens T-stop for a system that has an adapter on it. The T-stop field means the complete optical system as configured.
- Reading the depth-of-field equivalent aperture as an exposure setting.
- Assuming a computed f/1.23 requirement means some lens can deliver it. The figure is a mathematical requirement, not a hardware recommendation.
Tips
- Match on the axis you are protecting. Horizontal for a landscape wide, vertical when headroom is the constraint.
- If you are delivering to one aspect ratio, set the common delivery frame — then both axes match and the comparison means what it looks like.
- The depth-of-field equivalent assumes the same viewpoint. Move the camera to reframe instead and the perspective changes, which no focal length can undo.
Frequently asked questions
Does crop factor change the actual lens?
No. A 50 mm lens is a 50 mm lens on every camera it fits. A smaller sensor records a smaller part of the same projected image, so the field of view is narrower — but the optical design, the focal length and the f-number are unchanged.
Does equivalent aperture change exposure?
No, and this is the distinction the tool is built around. Scaling an f-number by the crop factor predicts a comparable depth of field for matched framing. It does not describe light. Exposure per unit sensor area depends on the f-number (or, more accurately, the T-stop) you actually set — a crop does not change it.
Which crop factor should I use for Super 35?
There isn't one. Cameras sold as Super 35 differ in active area, and the same camera differs between recording modes. Use your camera's published active dimensions for the mode you are shooting, or type them into the custom fields. A single Super 35 number will be wrong for most of them.
Does 4K always crop the sensor?
No. A resolution is not a crop. A camera may downsample the full sensor width to 4K with no change in angle of view, or it may read a centre window. Only the active area for that mode tells you which, which is why this tool asks for millimetres rather than a resolution.
Can I compare anamorphic lenses?
For field of view, yes — enter the squeeze and the tool models the horizontal axis correctly, showing the recorded and desqueezed shapes separately. For aperture it deliberately refuses: no single scalar f-number describes anamorphic depth of field or pupil behaviour, which depend on the lens design, so the tool shows nothing rather than a confident-looking guess.
Does a reducer change aperture?
Geometrically, yes. A 0.71x reducer concentrates the same image circle onto a smaller area, so the effective f-number improves by the same factor — about 0.99 of a stop. That is the ideal model. Measured transmission depends on the glass, so if you have a measured T-stop for the whole lens-plus-adapter system, enter it and the comparison is labelled as measured rather than estimated.
Why does one focal length not match the whole frame?
Because the two formats are different shapes. Matching the horizontal axis between a 3:2 sensor and a 4:3 sensor leaves the vertical axis mismatched, and vice versa. The tool shows the mismatch instead of averaging it away. If you are delivering to one aspect ratio, set a common delivery frame and both axes will agree.
Are my settings stored online?
No. Every calculation runs in your browser, there is no server to send anything to, and nothing is saved unless you choose to. Copy link puts the settings into the web address itself, so anyone you send that link to can read them — share it only with people you mean to.
My camera isn't in the list. What do I do?
Type the active width and height for your recording mode into the custom fields. That path is fully supported and is in fact more accurate than a preset, because it describes the mode you are actually shooting rather than a category average.
Related tools
- Focal Ratio Calculator
- Image Footprint Calculator
- Drone GSD Calculator
- KDP Manuscript Checker
- Image Metadata Privacy Cleaner
- KDP Interior Randomizer
Explore more in Publishing, KDP, Creator & Design.
Cite this tool
Zerdly. (2026). Lens Equivalence Calculator. Retrieved from https://www.zerdly.com/tools/lens-equivalence-calculator/
Tip: Enter any known values to calculate the remaining results.
Designed to run locally in your browser. Tool inputs are not intentionally stored by Zerdly unless stated otherwise.



